It does NOT make any direct cable connection to a mobo fan header. It requires connections to a SATA power output from the PSU, and to a second USB2 header of the mobo. The H510 Elite case comes with a device pre-mounted inside called their Smart Device V2. I understand that it is the front pair of these four that are your issue - specifically, the control of their speed. Two 140 mm AER RGB 2 fans come pre-mounted in the front, and you have also two additional AER RGB 2 fans, a 140mm at top and a 120 mm at rear. Separate from that, you have four CASE ventilation fans. You also should be able to "see" the PUMP speed in BIOS Setup shown as the "fan" speed on the CPU_FAN header. You are using the CAM software utility to observe and control that AIO system, right? On that you should be able to see the pump speed and the speed of the two rad fans (although only one fan speed will show) and configure those items. One of the small lines from the multi-headed cable coming from the pump goes to the CPU_FAN header, and there is another that connects to a USB2 header on your mobo. Two are mounted on the radiator of the Kraken X62 AIO system and are connected using a cable coming out of the pump on top of your CPU chip. I believe you have six fans all together. But it ALSO can control the mobo fan headers for you, so CAM can control all your fans, no matter which place you use to connect them. ![]() It communicates with the Smart Device via that USB2 connection cable. Alternatively, you can certainly plug those fans into any of the six mobo SYS_FAN headers.Ĭontrol of both fan speeds and lighting effects is done by the free downloaded CAM software tool. You MIGHT do that using another fan output port of the Smart Device. If you have other non-RGB fans for case ventilation (I believe one does come pre-mounted in the case rear) they need only fan power and control. It includes a note that, if you do this, you will need to tell the mobo in its BIOS Setup screens to Ignore the fan speed of the CPU_FAN header - otherwise it will give out error messages about failed CPU fans, and may even shut down. In the Notes regarding the ports of the Smart Device there is a recommendation that you connect your CPU cooler to one of this Device's fan ports so that the CAM software (see below) can control it for good but quiet operation. BUT the alternative is to use a different cable (supplied) to go from the last fan in the daisy chain to the light strip, so that it also is synchronized with the lights in the fans. In that arrangement, the strip lighting effects can be different since they are on a different output channel. The manual suggests that it should be plugged into the unused LED output port of the Smart Device. Now, the case also comes with at least one ARGB light strip pre-mounted in the case front. The problem I have is: why does the Smart Device have three separate fan output ports? MAYBE I misunderstand, and the fan MOTORS all have their own separate cables that go to these ports, while only the RGB lights in the fans are handled by the daisy-chain system. This puts all the fans on that chain under exactly the same signals from a single Smart Device output channel, so they are synchronized. Thereafter one uses other cables (supplied) to daisy-chain from the first fan to the second, and so on. ![]() Further, only one such connection directly to the Smart Device is needed. ![]() They appear to say that both the fan motor and RGB lighting components of each AER RGB2 fan are done though a single cable from the Smart Device. There's a detail not clear in their manuals. It also has three Fan output ports for control of fan MOTORS. The Smart Device has two LED output ports - view them as two separate "channels" for power and control of ARGB lighting devices. It has another cable that must go to a mobo USB2 header, and this is used for communication between the Smart Device and the NZXT CAM software tool running on the mobo. It has one cable that must plug into a SATA power output connector from the PSU for power to this unit. The case comes with the Smart Device V2 unit, and there are several connections to make for it.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |